Communicate with Supplier? Supplier
Jen Li Ms. Jen Li
What can I do for you?
Chat Now Contact Supplier

OPT Cutting Tools Co., Ltd.

Round Nose Mills - manufacturer, factory, supplier from China

(Total 24 Products for Round Nose Mills)

  • Two Flute  Carbide Ball Nose Mills

    Two Flute Carbide Ball Nose Mills

    • Brand: OPT

    • Packaging: Inner: Plastic case Outer:Gerneral Carton

    • Supply Ability: 8000 pcs/month

    • Min. Order: 10 Piece/Pieces

    OPT Unequal helix angle end mill OPT is able to supply customer with high performance tools in a very short lead time All brazed blanks are kept in stock and are finish ground to the hole dimensions tolerances and first cut geometries defined by the customer in their order We supply a comprehensive range of carbide...

    Contact Now

  • PCD round t-slot end mill cutter reamer

    PCD round t-slot end mill cutter reamer

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD round t slot end mill cutter reamer The success of the PCD tool machining have effct on the sharpening quality of the tool In order to extend the tool life the cutting edge of the tool must be strengthened with an appropriate tool sharpening method PCD tool sharpening varies with the material being processed and...

    Contact Now

  • PCD ball nose end mill plunge for nylon

    PCD ball nose end mill plunge for nylon

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ball nose end mill plunge for nylon When manufacturers use PCD tip shaped tools they can be slightly tilted on the carbide to increase productivity continuously process parts and extend tool life PCD tip shaped tools can be milled with a maximum cutting depth of approximately 60 of the PCD insert length OPT...

    Contact Now

  • PCD diamond round roll groove milling forming cutter

    PCD diamond round roll groove milling forming cutter

    • Brand: OPT

    • Packaging: Inner:Plastic case Outer:Standard carton

    • Supply Ability: 5000 pcs/month

    • Min. Order: 2 Piece/Pieces

    PCD diamond round roll groove milling forming cutter PCD tool grades are classified according to the size of the diamond particles According to the manufacturer s guidelines fine grained medium grained and coarse grained PCD grades correspond to the diamond size coarse grained PCD grades have higher strength and...

    Contact Now

  • PCD round end mill cutter in router

    PCD round end mill cutter in router

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD round end mill cutter in router Standard size full section PCD tools have a complete PCD top surface which is sintered on a carbide substrate Although full section tools start at a higher cost they are indexable and can be located on one side of the tool Provide multiple cutting edges At the time of purchase such...

    Contact Now

  • PCD ultra end mills cutter cornor radius

    PCD ultra end mills cutter cornor radius

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ultra end mills cutter cornor radius Standard size full section PCD tools have a complete PCD top surface which is sintered on a carbide substrate Although full section tools start at a higher cost they are indexable and can be located on one side of the tool Provide multiple cutting edges At the time of purchase...

    Contact Now

  • high quality PCD delta round roll forming cutter

    high quality PCD delta round roll forming cutter

    • Brand: OPT

    • Packaging: Inner:Plastic case Outer:Standard carton

    • Supply Ability: 5000 pcs/month

    • Min. Order: 2 Piece/Pieces

    high quality PCD delta round roll forming cutter When processing a slightly harder material PCD tools can be cut faster but even then the upper limit is about a line speed of 200 m min above which the wear is exacerbated Obviously the cutting speed can be much faster when processing ordinary cast iron and the right...

    Contact Now

  • PCD metric ball nose end mill long

    PCD metric ball nose end mill long

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD metric ball nose end mill long Safe and reliable blade retention plays a key role in the application of PCP tools especially for rotary tools Wedges and screws are now used in combination just like conical tools and wedges which improves the fixation of the tool Common thread and pressure plate design OPT cutting...

    Contact Now

  • PCD T-slot ball nose end mill taper miniature

    PCD T-slot ball nose end mill taper miniature

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD T slot ball nose end mill taper miniature When using PCD tools effective chip removal is very important Chips generated by PCD tools are very fast The machining system must continuously and quickly remove chips from the work area Coolant air mist chilled air and their combination all have an impact OPT cutting...

    Contact Now

  • PCD vortex ball nose roughing end mill

    PCD vortex ball nose roughing end mill

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD vortex ball nose roughing end mill Recent advances in the design and use PCD cutting tools have provided new incentives for manufacturers in different industries to increase productivity For example the automotive industry s use of new large particle monolithic PCD inserts makes it possible to efficiently machine...

    Contact Now

  • PCD roughing ball nose long end mill micro

    PCD roughing ball nose long end mill micro

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD roughing ball nose long end mill micro Standard size full section PCD tools have a complete PCD top surface which is sintered on a carbide substrate Although full section tools start at a higher cost they are indexable and can be located on one side of the tool Provide multiple cutting edges At the time of...

    Contact Now

  • PCD ball nose end dmill long flute

    PCD ball nose end dmill long flute

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ball nose end dmill long flute Safe and reliable blade retention plays a key role in the application of PCP tools especially for rotary tools Wedges and screws are now used in combination just like conical tools and wedges which improves the fixation of the tool Common thread and pressure plate design As well as...

    Contact Now

  • PCD ball nose end mill for machining plastic

    PCD ball nose end mill for machining plastic

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ball nose end mill for machining plastic Most PCD tools used today are point shaped A PCD blade was welded to a corner of a carbide bar PCD tool block sizes have been standardized in the industry and can be used in the sipes and milling slots of standard toolholders Unlike carbide tools PCD tools cannot be indexed...

    Contact Now

  • PCD miniature ball nose conical end mill titanium

    PCD miniature ball nose conical end mill titanium

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD miniature ball nose conical end mill titanium Now the majority of production users have overcome the sharp blade PCD tools have been found to be cost effective Because in most non ferrous metal processing PCD tools are significantly better than carbide tools which is not due to any development of the processing...

    Contact Now

  • PCD vortex ball nose end mill standard size

    PCD vortex ball nose end mill standard size

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD vortex ball nose end mill standard size When roughing alloy cast iron PCD cutting tools must undergo intermittent cutting caused by surface cracks residual sand and other discontinuities of the original surface left over from the casting process Good abrasion resistance also plays a large role in finishing...

    Contact Now

  • good PCD slotting standard ball nose end mill

    good PCD slotting standard ball nose end mill

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    good PCD slotting standard ball nose end mill According to the occasion the characteristics of the material to be cut and the specific requirements of processing will have the appropriate grade and particle size PCD compact used as a tool bit In general diamonds with high volume concentration or large particle size...

    Contact Now

  • quality PCD ball nose groove end mill radius

    quality PCD ball nose groove end mill radius

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    quality PCD ball nose groove end mill radius In order to achieve a dynamic balance of tool accuracy gravity is often used remove the appropriate weight in the appropriate part of the tool body to allow the actual imbalance of the tool to be less than the allowable imbalance Due to the superior performance of PCD tools...

    Contact Now

  • PCD ball nose end runner mill for rubber

    PCD ball nose end runner mill for rubber

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ball nose end runner mill for rubber Because the PCD tool is dynamically balanced Since the PCD tool is suitable for high speed cutting the dynamic balance of a rotating PCD tool is particularly important In dynamic balance the maximum allowable speed of the tool and the accuracy level of the dynamic balance...

    Contact Now

  • PCD ball nose end mill cutter for steel

    PCD ball nose end mill cutter for steel

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ball nose end mill cutter for steel PCD composite board not only has excellent properties such as high hardness high wear resistance high thermal conductivity low friction coefficient low thermal expansion coefficient etc but also has good strength and toughness of cemented carbide PCD briquettes are also...

    Contact Now

  • PCD ball nose end mill with corner chamfer

    PCD ball nose end mill with corner chamfer

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD ball nose end mill with corner chamfer Finding different PCD tooling techniques on the same machine is not straightforward High speed cutting has become a major development direction of modern manufacturing technology The PCD composite sheet composed of micron sized diamond particles which are uniformly mixed on a...

    Contact Now

  • quality PCD ball nose end mill for carve

    quality PCD ball nose end mill for carve

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    quality PCD ball nose end mill for carve The chip generation after PCD is so fast that you have to have an effective way to get them out of the work area continuously And we can use coolant air oil mist cooling air or any combination Before using any method you need to ensure good part quality and blade life OPT...

    Contact Now

  • best PCD ball nose end mill for aluminum

    best PCD ball nose end mill for aluminum

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    best PCD ball nose end mill for aluminum In order to replace cemented carbide with PCD in these applications we were looking for higher productivity as well as eliminating the need for longer tool life and part finish requirements for frequent tool changes The range of parts covered is familiar with everything from...

    Contact Now

  • PCD flute ball nose chamfer end mill wood

    PCD flute ball nose chamfer end mill wood

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    PCD flute ball nose chamfer end mill wood Rigid fixtures are equipped to give users more reliable results with PCD and help them take full advantage of the productivity potential of PCD PCD tools in the automotive industry they include cylinder heads cylinder blocks intake manifolds gearboxes and a large variety of...

    Contact Now

  • good PCD taper ball nose end mill engraving

    good PCD taper ball nose end mill engraving

    • Brand: OPT

    • Packaging: Carton

    • Supply Ability: 10000 pcs/month

    • Min. Order: 10 Piece/Pieces

    good PCD taper ball nose end mill engraving Most of the PCD inserts used today are insert type which means they contain a small piece of PCD welded to the corner of the carbide insert The insert inserts are factory standard so they can be mounted on the holders of standard carbide shanks and milling cutters But unlike...

    Contact Now

Review

Yaron Ben-david

Jun 28, 2020 5

I'm very satisfied with the Round Nose Mills , the seller is cooperative and responsive to my problems.
Jolly Zhang

Jun 28, 2020 5

I have to say, this is a amazing Round Nose Mills .
Darius Pavri

Jun 19, 2020 5

Excellent Round Nose Mills , OPT is very responsive and helpful, I would deal with again anytime!
  • Related Information
Our target should be to consolidate and enhance the top quality and service of current goods, in the meantime frequently create new products to satisfy diverse customers' calls for for Round Nose Mills , Round Nose Mill , Solid Ball Nose Mills , invite all intrigued prospective buyers to visit our web page or get in touch with us specifically for additional info.
"Our solutions are widely identified and trusted by people and might fulfill continuously transforming economic and social demands for Round Nose Mills , Round Nose Mill , Solid Ball Nose Mills , we will give you a surprice for Qulity and Price.

Send Us a Message

We didn't put all products on website. If you can't find the product you're looking for, please contact us for more information.

Send Inquiry

Jen Li

Ms. Jen Li

Tel:86-755-27579101

Fax:86-755-27570606

Mobile Phone:+8613928413454Contact me with Whatsapp

Email:opt@tongweicn.com

Address:Room 609,Building 1,Dulex Hi-tech Park,Longhua District,Shenzhen,China, Shenzhen, Guangdong

Mobile Site